氧化铝耐磨陶瓷管
....................................
氧化铝耐磨陶瓷板
....................................
陶瓷管
....................................
耐磨陶瓷管
....................................
分料器
....................................
耐高温陶瓷胶粘剂
....................................
可调节式膨胀节
....................................
下料弯头
....................................
耐磨陶瓷阀
....................................
耐磨陶瓷片
....................................
耐磨陶瓷贴片管道
....................................
耐磨涂料
....................................
 
地 址:宜兴市宜城街道南园
电 话:0510-87458772
传 真:0510-87458772
联系人:蒋工 13961597233
蒋总 13961571887
邮 编:214225
网 址:www.yxchenhong.com
邮 箱:sales@yxchenhong.com
 
下料弯头
   
 
公称通径(Ф)
法兰孔中心(Dmm)
法兰外径(Dmm)
螺孔数量直径(Dmm)
下料出口直径(Dmm)
法兰中心(Dmm)
法兰孔外径(Dmm)
螺孔数量
其他进出口尺寸
A
B
C
D
E
80
200
235
8-18
300
445
485
12-23
320
530 420 477 225
100
225
260
8-18
300
445
485
12-23
320
530 420 477 225
150
280
315
8-18
300
445
485
12-23
375
530 420 425 250
200
335
370
12-18
300
445
485
12-23
375
530 420 552 250
(安装说明)
 瓷衬耐磨瓷管,结构形式如图(1),是将工程耐磨陶瓷内衬于钢壳以内,两端法兰和其它管道相连。所以安装时请按下列要求操作:
 1.严禁用锤子等金属敲击钢壳,外表及两端瓷面,以免损坏陶瓷。
 2.瓷衬管和瓷衬管相连时,中间加3-5mm石棉垫,然后用螺栓均匀拧紧,如图示(1)
 3.瓷衬管和钢管相连时,请先将非标法兰套于钢管上,加石棉垫片,并用螺栓固定法兰,螺孔,然后点焊,非标法兰和钢管固定。再松开螺栓,将非标法兰和钢管焊牢,如图(2)
The strucural form of the procelain-lined anti-wearing ceramic tipe is as Shown in fig(1).It is to put the anti-wearing ceramic inner spacer in the Case with its two ends joined to the other pipelines with a flange.
It should be installed according to the follow-ing operatins demands:
1.It is strictly not allowed to strike the steel case.the outer surface and the ceramies faces at the two ends with a hammer or other metallic articies to avoid damaging the ceramies.
2.When the two porcelain-lind pipes are going to be joined to gether,be sure to use an asbesto spacer (Attached with the product)of 3-5m to Beplaced between them.Then get ti tightened with a bolt as shown in fig.(1)
3.As the porceanin-lined pipe is Going to be joined to the steel pipe,please,first,get the nonstan-dard flance to be covered on the steel pipe with an asbestos spacer and let the flange and Screw fixed up with bolts.then.get Them to be spot-welded.Loosen the bolt as the nonstandard flange and steel pipe are both fixed up.then.get them welded tight.asshowninfIg,
 
耐磨陶瓷-耐磨陶瓷管-公司介绍-产品分类-资质荣誉-工艺流程-客户案例-网上订单-联系我们
宜兴市晨泓耐磨陶瓷有限公司 版权所有
地 址:宜兴市宜城街道南园 电 话:0510-87458772 传 真:0510-87458772